Tools - Specialty Tools |
|
|
 |
ARC360 HOLE CUTTERThe tools on the market for cutting lightning holes in your airframe parts have never impressed me much especially if the holes are larger than a couple of inches in diameter. Panel knock put punches and hole saws work well for holes that are aren’t too big but it gets harder and more expensive as the size of the hole increases. View more details |
| 12-01977 | NOAH ARC-360 HOLE CUTTER | $98.95 | 
| |
|
 |
CUSHIONED CABLE CLAMP
(ADEL CLAMP) INSTALLATION PLIERSThese special pliers allow for greatly simplified installation of single or multiple Adel type cushioned clamps. The pliers securely hold the aligned clamps in position, allowing for easy installation of securing hardware. Each kit includes special plier, alignment awl, and simple instructions. View more details |
| 12-02017 | CUSH CABLE CLAMP INSTL PLIERS | $36.85 |
| |
|
|
 |
BOGERT COMANCHE
BUNGEE TOOLLower damage risk with the right tool. Complete control of bungee shock cords coming off. Complete control of bungee shock cords going on. E-Z instructions with detailed drawings. Safe landings depend on new cords every few years. View more details |
| 06-00419 | BOGERT STRETCHING TOOL | $79.85 |
| |
|
|
|
 |
NON-CONTAMINATING SCRAPEROur Non-Contamination Scraper is suitable for all airframe scraping operations. It will not contaminate delicate aluminum parts with steel particles which can induce corrosion. View more details |
| 12-30205 | NON-CONTAMINATING SCRAPER | $21.60 |
| |
|
 |
CESSNA COWLING FASTENER DRIVERSlotted type cowling fasteners are not easy to fit with generic common screwdrivers. To overcome this, this driver has a broad hollow cut tip that accurately engages the drive slot. Additionally, a no mar, spring loaded, plastic sleeve simultaneously guides the tip by fitting around the outside diameter of the fastener head. View more details |
| 12-17615 | CESSNA COWLING FASTENER DRIVER | $22.85 |
| |
|
 |
TURNBUCKLE CHAIN TOOLThis tool consists of two clamps joined by sprocket type (bicycle) chain. When clamped to cable and fittings at each side of the turnbuckle, anchor the cable to allow free adjustment of the turnbuckle. The adjustment becomes a two hand instead of three hand adjustment. View more details |
| 12-01794 | ECON TURNBUCKLE CHAIN TOOL | $38.50 |
| |
|
 |
SWIVEL HEAD PIN VISEHas two double-end collets with a capacity of .0 to .187 in. or .0 to 3.2mm. Screw chuck tightly holds small drills, burrs, wire and miniature tools. View more details |
| 92 | SWIVEL HEAD PIN VISE #92 | $9.75 |
| |
|
 |
JOGGLE-360 FABRICATION TOOLAdjust the guide rollers to the desired set back or width of joggle by rotating the Eccentric Guide Roller Adjustment Screws with an Allen wrench. View more details |
| 12-02252 | NOAH JOGGLE-360 FAB TOOL | $99.00 |
| |
|
 |
BLIND SKIN SCRIBEFor use on flush skin butt joints. This tool quickly and easily finds the cut line on the overlap of new metal. The lower leg slides under the new metal and hooks on the adjacent skin and the upper leg scribes the new skin as it pulled along. View more details |
| 12-00746 | BLIND SKIN SCRIBE | $33.75 |
| |
|
 |
S4-3 RACE REMOVAL TOOLThe S4 magneto seal installation, inner and outer race installation tool is three tools in one and is proportioned in such a way that it is easily accommodated by most small bench arbor presses. View more details |
| 12-17603 | S4-3 RACE REMOVAL TOOL | $89.75 |
| |
|
 |
S4-2 RACE REMOVAL TOOLThe S4 magneto drive end inner race removal tool works in conjunction with a standard bearing puller. The split gripper ring fits behind and around the race and is captured in the puller ring by two opposing set screws. A groove on the puller ring provides the point of attachment for the puller arms. View more details |
| 12-17602 | S4-2 RACE REMOVAL TOOL | $127.95 |
| |
|
 |
SWIVEL HEAD PIN VISEHas 2 double-end collets with a capacity of 0 to .187 in. or 0 to 3.2mm. Screw chuck tightly holds small drills, burrs, wire & miniature tools. View more details |
| 92 | SWIVEL HEAD PIN VISE #92 | $9.75 |
| |
|
 |
CANOPY BREAKER TOOLEveryone who flies at one time or another has given thought to potentially being trapped in an aircraft with few options for escape. To compound this predicament you can enter into a water landing, have leaking fuel or fire issues and you really don’t have a viable escape plan. Plexiglas is not very thick but still difficult to break with a hand, fist or elbow. What if you had the foresight to attach a device inside the cockpit that gave you an option – a Piranha Canopy Breaker Tool attached to the airframe which can be easily reached in these types of emergency situations? View more details |
| 12-02269 | CANOPY BREAKER TOOL | $54.85 |
| |
|
 |
RIB ALIGNMENT TOOLThe R.A.T. Tool is the only tool designed specifically to repair damages to the upper and lower open rib trailing edges of the aircraft controls. View more details |
| 12-02364 | RIB ALIGNMENT TOOL | $219.95 |
| | 12-02409 | RIB ALIGNMENT TOOL KIT | $189.95 |
| |
|
 |
DECAL ERASER WHEELFor quick and easy removal of decals, pinstripes, bumper stickers, reflective tapes etc from glass and OEM painted surfaces without any damage. Also very effective in removing adhesive tapes and glue from the back of moldings. View more details |
| 12-02401 | DECAL ERASER WHEEL 4" ERW | $14.85 |
| |
|
|
 |
BENDIX MAG LOCKThis Bendix Mag Lock works on S4 and S6 and other Bendix Mags. To use simple place a cotter pin loosely into lower plunger hole. Screw sleeve into magneto case. Align red slot in plunger parallel to mag tooth gear. Remove cotter pin to engage gear tooth. View more details |
| 12-02243 | BENDIX MAG LOCK | $53.75 |
| |
|
 |
PITOT TUBE INSTALL TOOLThis tool was developed, in response to fleet owner and FBO requests. They were having experienced difficulty installing Covers onto high wing Pitot Probe locationss, e.g., Cessna Caravans, Bush aircraft with Tundra tires, float planes and amphibians. In field trials it was found that this tool is also very useful to install-remove the same Covers onto over-the-nose Pitot Probes, of VeryLite and commercial jet aircraft! View more details |
| 13-06672 | PITOT TUBE INSTALL TOOL | $78.50 |
| |
|
 |
BULLSEYE PICKSThe bullseye pick was originally used in the dent repair/collision trade, but also works great for restoration work. These are ideal to reach in around the edge of a panel, around a gusset, or into a blind area to repair the dent from the backside. View more details |
| 12-02292 | 15" BULLSEYE PICK | $84.25 |
| | 12-02293 | 25" BULLSEYE PICK | $94.75 |
| |
|
 |
8 FOOT RADIUS BRAKEThis sheet metal radius brake is the perfect solution for forming radius bends in mild steel and aluminum. Stress and cracking of material is minimized due to the unique design of the apron, which swings outside the radius and rolls across the material. View more details |
| 12-02348 | 8 FOOT RADIUS BRAKE | $2695.00 |
| |
|
 |
SK-SP5 SKYBOLT CLOC TOOLSpecifically designed to preset and adjust CLoc® 4000 Series Adjustable Receptacle and Mounts. Locking Sleeve can be set for known panel thickness to preset SK215, SK245, and SK2003 Dash 5 Series receptacles. View more details |
| 08-07210 | SK-SP5 SKYBOLT CLOC TOOL | $41.75 |
| |
|
