The GDL 82 Automatic Dependent Surveillance-Broadcast (ADS-B) datalink, is the latest addition to the comprehensive lineup of certified ADS-B solutions available from Garmin. GDL 82 is a small, lightweight Universal Access Transceiver (UAT) datalink with a built-in GPS receiver. For aircraft owners looking for an economical and turnkey solution to satisfy the requirements of ADS-B “Out”, GDL 82 is a straightforward path to meet regulatory requirements.
GDL 82 broadcasts on the 978 MHz frequency, providing a rule-compliant ADS-B “Out” solution for aircraft operating below 18,000’ in the United States. Installation is quick and easy because GDL 82 utilizes a patent-pending design, in which GDL 82 is installed in-line with the aircraft’s existing transponder antenna wiring to transmit the necessary ADS-B “Out” information. The WAAS GPS receiver required for ADS-B compliance is built-in and a GPS antenna is included to offer additional cost-savings for aircraft owners without an existing WAAS GPS on board their aircraft.
82 also contains AutoSquawk interrogation technology, whichGDL interfaces with most Mode C general aviation transponders to synchronize the squawk code and pressure altitude information from the transponder with GDL 82, eliminating the need to install a separate dedicated UAT control panel and altitude encoder. (Please reference the installation manual to determine if the existing Mode C transponder meets compatibility requirements.) This technology not only simplifies installation but also eliminates the burden of the pilot manually keeping the squawk code in sync.
Pilots who already utilize an ADS-B “In” receiver — such as the GDL 52, GDL 39/GDL 39 3D and the Stratus line of portable solutions — can receive additional benefits as the GDL 82 complements many existing products on the market. With ADS-B “Out” participation, pilots using these products have access to a more comprehensive ADS-B “In” traffic picture, resulting in improved situational awareness.
Just installed the GDL-82 in my Twin Comanche with no install issues, install took 12 hours. Downloaded the Install Tool and the configuration went well. So far so good pulled plane the plane out of the hanger and did a ground check and everything booted up with no faults. I will do the test flight soon I dont see any issues moving forward. George K.
Delivered promptly in good condition. Unit worked as advertised. Wiring harness not so much. The wires for the anonoymous switch and annunciator light were in the box but not in the connector. Had to order and wait on a d-sub micro extraction and insertion tool to do the install. Blank pins were in the positions for those positions. Slowed the install down by a couple days and I paid for a completely wired harness.
I am unable to review it as I havent had time to install it!! All the parts came in the package so Im hoping it will work as advertised!
So far no complaints. This is what the csr who dosent want to put much money into a system but have something that works. We have installed 2 so far. Some minor issues with installation but nothing we couldnt work through.
I have installed 4 of these. Easy and solid results. I am not a professional installer just a experimental homebuilder. I would discourage the pre-made harness as the wiring is very simple to make. Havent had any trouble with the USB pigtail or pins. One thought would be for Garmin to pre-crimp at least the USB pins at the factory to avoid issues. Especially if what another reviewer posted is correct and Garmin cant provide replacement pins for the USB pigtail. The rest of the harness could then be fabricated in the field. I added the anonymous mode remote switch to every install. The great thing about the 82 is no additional transponder antenna and being out only. That leaves the options for in wide open now and in the future.
First of all, let me say that these complaints are directed at Garmin, not ACS who delivered the device in good shape in a timely manner. First of all, I didnt need the GA 35 antenna, but was forced to purchase one along with the GDL 82. I would like to see Garmin offer just the box without the antenna. Secondly, the unit comes with no instructions whatsoever. ACS has the 80 page installation manual here under Documents, so that has to be downloaded first. That document has most of the information you will need, but not all. As others have mentioned, the USB connector is cheap and has two #28 wires that require a special crimper. I ended up soldering mine. The instructions should have elaborated on crimping those tiny and fragile wires. If I had it to do over again, I would have ordered the optional harness. Garmin has a series of helpful videos that perhaps ACS might want to link here. https://fly.garmin.com/fly-garmin/support/articles/?tags=region_aviation&tags=product_aviationproductfamil&tags=region_avhowtooperation&searchText=gdl%2082 Finding the GD8X install tool at the Garmin site was difficult. One would have thought that the installation manual would have provided a link, but it didnt. Once I found it and installed it, it left an Icon on my desktop for the _install_ program, but not the _configuration_ program. I finally found the latter in C:/Program Files (X86)/Garmin/GDL 8X Install Tool/GDL8XInstallTool.exe. The program worked flawlessly when I finally found it and brought it up. I found my ICAO code on the FAA site by looking up the registration for my tail number. The last link that would have been helpful was the FAA ADS-B performance site where you can request a performance check when the installation is complete. https://adsbperformance.faa.gov/PAPRRequest.aspx . They send you a report via email 30 minutes after you fly. The installation was straightforward once I had all the information I needed, and the unit works as advertised.
Unit has not been installed at this time. Will follow up when done so.
As far as avionics go, this was amazingly simple to install. Had to be a bit intuitive/logical as directions were a bit weak. Attached to laptop, uploaded data, went flying. Flew the rule airspace, pulled my FAA report. Wow. Cool. Along with the Foreflight and Scout, Im complete IN/OUT! So far, so good!
I ordered the harness but only used the voltage in (red and black) wires as I had no other Garmin equipment to interface with. I paid for next day air on thursday, but I would have gotten it in the same time as regular ground.
The box comes with the GDL 82, GA 35 WAAS GPS and the installation kit. You will still need coax cables from the GDL 82 to the transponder antenna and the unit to the WAAS GPS antenna. You will also need wire to draw up the wire harness for the unit.
No. The GDL 82 is only an ADS-B out unit. It does not perform ADS-B in functions.
Yes, this kit comes with the Garmin GA 35 WAAS antenna.
Yes, it is. Though you will want to get a transponder test to make sure your unit is operating properly.
The GDL 82 powers on with the aircraft.
Yes. The gdl-82 will interface with the 327 antenna output to make the signal compliant.
You will need a BNC male to BNC male cable. BNC connectors are based on the inner pin, not the housing. The GA 35 WAAS GPS antenna has a TNC female antenna connector on it.
Yes. Per Garmin, this unit will work with any mode C transponder that is in good working condition. A transponder test is recommended to ensure that the unit is operating properly.
Yes, it is.
You will need a GPS 20A with a connector kit and a GA 35 antenna. This unit can give GPS info to the G5 without having to buy a second antenna for the G5.