FREE SHIPPING ON ORDERS OVER $350 (USA ONLY - SOME EXCLUSIONS APPLY) | 877-4-SPRUCE

Socoglaze Epoxy Propeller Coating - Aerosol - Gloss Clear

$37.50/Each
Quantity
Add to Wishlist
Part# 09-04674
MFR Model# 102700-112

Overview

Socoglaze Epoxy Propeller Coating is a general purpose epoxy aerosol. It is intended for use over metal and composite surfaces that are bare, scuffed, sanded, abrasive blasted, primed and previously painted surfaces while showing excellent protection. Aerosol

Certification paperwork must be requested at time of order. If certs are required with purchase, please contact us by clicking here or calling sales.
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Documents

Reviews

I painted 8 prop tips in red and white. I shook the cans a lot before spraying and in between spraying. I turned the can upside down and sprayed until the nozzle sprayed clear when finished. I also stored the cans upside down as recommended. The work was done over 3 days. The spray came out as it should each time of use, there were no cases where the spray dribbled, or was not a fine spray. The colors look good. As with any spray paint, its necessary to be careful not to direct the spray at one spot or it causes curtains, as my father would call it, or it pools.....keep the can moving. A very good product, Ive just ordered more.

Ray M
July 30, 2020

Wotked well on multiple days. Flat finish was even. Covered well

Robert M
April 5, 2018

I had some issues with the paint due to high heat and humidity conditions. I called PTI directly and explained my problem. They took the time to replicate the problem in the lab and offer me a solution. Great customer service from PTI. If you order this paint from AS and are in extreme conditions make sure you inform them. PTI will change the chemistry of the paint to match the conditions.

Steven D
October 18, 2017

The flat grey was aokay. The black spat a little. Overall happy with the turn out after a 2000 grit polish.

Evan
September 1, 2020

The clear epoxy spray worked really well. Applied in 65-70 degree heat and made several light coats allowing the epoxy to build up. Between coats it’s essential to purge the spray nib or it’ll block up for sure. I waited 30 mins between each coat. It cures super hard and looks good. It did give my white prop tips a slight yellow tint though. Not enough to bother fixing but I know it’s there and it’s a bit annoying. One point off for that.

Luke T
September 8, 2019

Orders the sociglaze to paint a prop. In my 35 years in aviation. This has to be the worst paint I have come across. I shook the van for 3 minutes to make sure it was mixed well. The spray was splotchy with intermittent blobs coming out. Ruining the job all together. Will not use them again

Chris M
August 16, 2022

Product ( 2 cans) expiration date 07/2020. Neither can would evenly spray or coat. I asked for refund.

Doc H
April 13, 2020

This paint went on my propeller terribly. I DA sanded the surface and cleaned thoroughly prior to application. It would not flow out and is blotchy and the surface is rough. I suppose it will do for another year but next annual Ill be removing my prop and taking this coating off. Ill find another paint for next year. I would not recommend this paint.

Mark K
November 5, 2017

I ordered Socoglaze because Tempo was out of stock. The flat black was unacceptable. It splatters paint out in splotches or sprays out almost transparent fluid and occasionally seems to work ok. I shook the can for a very LONG time and it seemed to help a little but it is still completely unacceptable. You cant rely on it for painting your propellor.

Da
June 3, 2022

My experience with this paint was horrible. First pass clogged after 0.5 seconds. Continued to clog after shaking, changing nozzles, etc. Finally got some spray out of it and then started shooting goobers of who knows what. Clean these off, try again. This happened four times. After that the can went into the trash and I went to HD for good ole Rust-Oleum. Sprayed just fine. Problem now is I have 5 other cans of this stuff in different colors and am afraid to even start with it. And, yes, it was totally in date.

Michael M
January 3, 2021

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Is this PTI Epoxy Propeller Coating in an aerosol can? How long does it take to dry? Any special preparations before painting?

It is in an aerosol can, and dries in approx 20 minutes. The tech data sheet is available on our web site for more details on preparation.

Q: Is the PTI Epoxy Propeller Coating a top coat or a primer?

It is a top coat paint.

Q: Can I spray green zinc chromate primer on a prop to cover metal exposed edges and painted areas simultaneously? I will then top coat with epoxy propeller paint. All paints are in aerosol cans.

The zinc chromate primer is best used with something other than a urethane or epoxy topcoat. The reason is that the solvents in those coatings can wet in to the primer and destroy adhesion.

With that said, we believe that if you allow the zinc chromate to dry 48-72 hours the epoxy coating should not lift the primer. We do of course recommend using our epoxy propeller coating because the solvents in that coating will flash off quickly. If the zinc chromate is dried hard those solvents should not have time to penetrate it. We recommend that you test whatever epoxy coating you intend to use to make sure that your adhesion is not negatively impacted. Let us know if there is anything else.

Q: What paint and primer is best for my propeller?

Per PTI: The primer you would want to use is the zinc chromate or zinc phosphate. The epoxy propeller coating listed on this page is the top coat for props.

Q: Is the PTI Epoxy Propeller coating designed to be sprayed on bare aluminium propellers? The tips of my propeller are exposed and are showing signs of corrosion.

It can be applied to bare aluminum, but it must be clean and free of oils, grease, salt, etc. Primer can be used if desired.

Q: Can I buy this thing in like say a few ounces?

We only have the PTI prop paint in the aerosol can this time.

Q: Can PTI Epoxy propeller coating be sused on wooden propeller?

No it is designed to be used over metal and composite surfaces.

View in Catalog

View Image View in Catalog