Designed for those of you that want your plane to look like a jumbo jet in the pattern, skunk works and using AveoMaxiChip™ technology, here is the ultimate landing light. The Hercules™ is nonpareil in the industry as verified by test pilots at major aircraft manufacturers in night runway tests against all competitors' lights. Again, featuring the landing, taxi, and wigwag functions, the Hercules™ is also available with TCAS activation for recognition mode.
Voltage input 9 to 32 VDC, please remove legacy strobe boxes first!
For Experimental Use Only
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
These are super landing/taxi lights. On the Hercules light being for experimental category aircraft only: I think not. The Hercules lamp, without the bracket, is a virtual drop in for the standard 4509 or 4509Q landing lights. FAR Part 43 allows owner/operators to replace bulbs as long as they are of the same rating. The Hercules is rated at 14 volts 100 watts, virtually the same as a 4509. There is no requirement to get an approval if you install a replacement bulb from a different manufacturer. Part 43 does indeed allow you to replace bulbs of any kind at will, so long as you use something that doesn't draw any more power or require any major modification to the frame. Unless you are rewiring the landing light circuit to use the various optional functions that the Hercules allows: hi-low, wig-wag, you only need to make a simple log book entry, no 337 form, no A&P sign-off required under Part 43. If you want the other options, an A&P can sign it out, again without a 337.
This unit is voltage regulated from 9 to 36 VDC however comparing a 24/28 volt supply to a 12/14 volt supply, a 15% output loss (watts and Lumens) at 12/14 compared to 24/28 volt operation. At 75F degrees (24C) ambient temp., output is reduced to about 80% output after about 5 minutes of operation,with all 30 LEDs lit. After 5 minutes of use at those same ambient temps, about 50 watts using only 18 landing LEDs. Also about 75 watts with all 30 LEDs lit after that same 5 minutes. Peak Lux at 26VDC 12% less (13VDC 20%) than Aero LEDs 36-4596 100 watt unit at 26VDC using all 30 LEDs 40% less (13 VDC 50%) Lux than The Aero LED using the 18 landing LEDs. This unit does not loose output due to temperature nearly as quickly as the Aero LED unit does. It also offers more options (flexibility) built in wigwag features, and 3 illumination modes, Landing (18 LEDs, taxi (12 LEDs) and both (all 30 LEDs), lower 1/2 output settings for all 3 modes. It also offers wigwag. All in all, we will use this for wigwag dual recognition lighting and taxi operations. We will keep using HID systems for landing since there are still no LED units that can come close to the performance of HID for a true (far reaching beam) landing light especially the 50Watt and higher HID wattages. HID does not loose brightness at all as it warms up. I would not recommend this LED or the Aero LED units for any cowling locations, NO LED unit will perform well there. They get too warm (ambient air temps) to have much output in those locations unless they are directly ducted with cooler outside air. We were hoping that LED would be a good total solution but its not there yet even now in 2018.
Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
No, this product is not FAA Approved for use in certified aircraft. Only the Aveo Galactica series lights hold FAA Approval. A keyword search of Aveo Galactica will bring up all current certified models by Aveo.
The Aveo Maxx Hercules LED landing light Part #11-10639 is the version without the bracket. This is a Drop in replacement for Par 36 housings.
Current draw: Taxi -> max. 2.2A (12V ), Landing -> max. 3.5A (12V ), Landing + Taxi -> max. 5.6A (12V ). Aveo doesn't have a recommended wire for use. While a shielded wire is not needed it is recommended.
These are priced and sold individually, one light.
Yes that is correct.
Landing: HIGH 108,000cd/3700 L | LOW 58,000cd/2000 L
Taxi: HIGH 66000cd/2300 L | LOW: 33000cd/1500 L
Total: HIGH 170000cd/5900 L | LOW: 92000cd/3300 L
No this is a standard par 36, Aveo makes a brackett if you need it. It should fit in your original housing if your previous light was PAR 36.
40 degrees by 20 degrees.