The customer service was great. The product not so, upon use, the paint clogged the nozzle & would not function. can now on the shelf to be tossed.

Les S Verified Purchase

TEMPO FLT WHT EPOXY PROP COAT

I use this to paint my spark plugs because I hate when they turn rusty. I used regular paint before and it just chipped off when using the spark plug socket. After using this paint and the spark plug socket this paint DOES NOT chip. I am now going to use this to paint my brake calipers.

HD product. Long lasting. Very good service at your company. Thanks for the quick shipping.

Best product Ive found that actually holds up. Downside is that you have to shake the can a lot to get everything to mix well and you cannot forget to clear the nozzle after use. IF you dont, it gums up fast and can render a near full can useless after one use. Paint cures fast too. Typically within 1/2 hr after application, aircraft is good to go.

The Black worked as intended. Lambert Havelka

It works good if you keep shaking it while you spray it.. make two or three passes and shake the can two or three times

Excellent product ... when you can get it out of the can , great wear protection on rotor blades when applied the problem is the can , some cans spray very well others nozzle constant clogging and spluttery spray some cans go straight in the bin after any use and other used time after time till used up , wish it was available as normal paint and use a spray gun.

Its hit and miss with these rattle cans. I found that it can take up to twenty minutes of shaking to get an almost even spray. I only use it for small touch up areas and nothing large. Also found out unlike most professional paints that no matter how careful the prep after four hours you can still peel the paint off the prop when applying a second color.

I like this paint and have used it on many parts of my plane, nice spray width and consistent if you keep shaking. It takes a little more than expected so buy more than you think you will need. I have used 10 cans over the last 3 years and had no problems until the last can, test spray was good but half way through the first pass is started to sputter and get chunky, dripping out of the nozzle too, swapped to a nozzle from another can but was no help. Can was garbage. Plan to spray fair amount on the test piece for each can at the start so you dont have to strip the 3 coats you have on already to fix after a bad can.

The fumes are extremely strong and will cause headache almost immediately. I would only use it outdoors or in a hanger. Take warnings on label seriously.

Be aware that no two cans are the same... Perfect black coats.... White can came out like silly string after vigorously shaking it for 15 minutes... Ruined an otherwise perfect application... Complete do-over twice....

I was surprised just how hard a spray can of Flat Black Epoxy paint was to find couldnt be had at any big box or paint outlets in my area. Delighted when I located it at Aircraft Spruce & Specialty Co. The key to any good paint job is preparation and I sanded, cleaned, and tack clothed my project to a high degree. Following directions on the can regarding application, temperature, and re-coating I ended up with results that fell far short of my expectations. The finish came out un-even some parts glossy whilst others parts look like they were dry sprayed. About the best I can say about it was: I wanted a black color and thats what came out of the can.

Black worked fine, went to paint the tips white and during the process the paint began to come out stingy and in gobs. Ruined the job do over.

Dont buy. The gray coated the prop, but will have to be sanded and polished to get an acceptable finish. Despite extensive shaking, the can occasionally shot out globs of thick gray goo onto the paint job. When I tried to use it again one week later it refused to spray anything other than clear solvent.

Shook the can for one minute it sprayed about two seconds and then started splattering and running down the front of the canned dripping in the floor tried shaking another three minutes same results but Aircraft Spruce being a great company replace the paint for me

Ill give 2 stars as an average.... The first 2 cans of white came out like silly string after 10 seconds or so. The replacement from a new batch didnt have any problems. Sprayed a test piece and the pattern was good. Sprayed the prop and it was goopy and chunky. Despite the replacement being acceptable, the fact that the prop had to be stripped and painted again is the reason for the 2 stars. Aircraft Spruce had great customer service in fixing the problem, though.

Hopefully I just had old product. Rattle was slow to move compared to Gray and Flat Black cans. White pigment clogged nozzle very quickly and spit clogs. It was unusable. Aircraft Spruce is sending me another can.

John V Verified Purchase

TEMPO FLT WHT EPOXY PROP COAT

The product is fine and it arrived on time. However, it was the wrong item. Specifically, Im painting a propeller. It is Gray - so I ordered Tempo Propeller Gray epoxy paint. Flat black arrived. When I called your company to ask about how to exchange or make it correct, the operator said I ordered it online and its my problem. Reality check - I KNOW I ordered it over the phone because I ALWAYS order over the phone and remember talking to and order agent. My preference, which you dont carry, was for Gloss or Semi-gloss Black, similar to the finishes McCaluey propeller is using. SO, I settled for your Semi-gloss Gray. St least thats how I left the conversation. This has been my experience. John Marabella, Sarasota, FL

Horrible. As someone else said, after a few seconds, the paint comes out in globs. I’m now going to have to strip the paint and do it again with hardware store paint. This stuff is horrible. The can also leaks around the nozzle so I have paint all over my hands and clothes.

OK, after talking with Spruce about the problem of the epoxy resin settling out of the solvent base and coming out like goop when you try and spray it, as previously mentioned, apparently cold temperatures cause the problem. Which is interesting in that I bought black at the same time and worked fine.? If you buy white please test it as soon as its received to confirm performance and store it at room temperature on its side.

I followed all of the directions as instructed. When applying the paint it would go from an aerosol spray to a thick line of spaghetti. Very frustrating experience to say the least.

Unless the prep is done perfectly, this paint will peel. I have NEVER had this paint pass a certified peel test (24 hour wet sponge followed by a peel with mil spec masking tape). As for the advice to strip a blade before painting - bad advice. Some of the prop shops add paint to static balance so one blade could have three coats while one has only one. This can cause a large dynamic imbalance. As for using stripper on a constant speed prop - none of the manufacturers or prop shops recommend field stripping due to the risk of stripper seeping in the hub/blade area..

This paint does NOT even closely match a Hartzel Prop! Also, after much shaking and clearing the spray to make sure it sprays evenly, suddenly SNOT comes out! Like silly string, ruining everything I was hoping to accomplish. Never again!

Can was obviously defective. Paint went everywhere but where it was supposed to go. Fortunately customer service replaced it but it’s too cold right now to,paint.

Terrible product. The white sprayed nice at first then started clogging. Completely ruined the job. The other colors worked good.

This product should not even be sold at AS. You get one burst of normal paint then it comes out as a cottage cheese gloopy mess. We tried to use this in optimal conditions as far as heat and humidity and it just doesnt spray. Do not recommend.