EVERYTHING FOR PLANES AND PILOTS SINCE 1965 | 877-4-SPRUCE
Thumbs 1
Thumbs 1

SURF MTD MIC & PHN JACK HS BEI

$19.75/Each
Part# 11-01120
MFR Model# FAP 08-2

Overview

Metal housing available in Powdercoat finish, 2-hole .380 w/key, can be used on mic & phone jacks, intercoms, fuses, switches etc. Can mount with (4) small screws on outer flange.
(Flange NOT predrilled & hardware NOT included)
Powdercoat finish Aluminum .040
Dimensions W 2.9" X L 3.56" to outer edge of flange X H 1.06
Outer flange 1/4"
Holes .380 dia x 1.0 between centers
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

  • Frequently Purchased With
  • Customers Also Viewed

Reviews

Used on outside of side panels. Tried recessing but too hard to plug-in. Very good quality

Michael S Verified Purchase

SURF MTD MIC & PHN JACK HS BEI

December 11, 2021

These are ideal for mounting mic and audio jacks, either surface mounted or recessed. First off, enlarge the jack holes if necessary, with a correctly sized step drill. If you find that the angle of the installed jack will not allow the plug to be inserted, simply use a punch, inserted into the jack, to slightly bend the jack outward to allow the plug to be inserted without interference. When surface mounting, a hole large enough to insert a jack, must be drilled. This will be hidden when the housing is attached to the panel. If you flush mount the housing, cut a square hole in the panel, JUST large enough to allow the body of the housing to drop in, leaving the rim of the housing on the surface of the panel. These are extremely handy items due to their versatility. Just have to use some imagination.

Web
May 10, 2020

Quality material, and great price.

Cindy
November 14, 2019

I am not sure about the other low reviews on this product. Put in one two-jack and one four-jack in the back of a cabin Waco for a PS 3000 system. Jacks fit perfect and easy to install. Bought the aluminum one and powder coated to match. NO issues.

Neal G
November 3, 2018

There are many variety of this housing with different hole designs check with AS. Also the connectors can be first installed in housing then can be easily be bent for wiring or desired plug angles.

Ken
February 7, 2018

Appears to be well made and was as advertised. Usual great service and delivery

Stuart R
July 14, 2020

Does what it needs - simple. Basic. I ended up having to use a step-bit to ream out the holes for the jacks. I needed to go up a size to accommodate the insulating washers. Not a big deal. I also drilled out 4 corners so I could use sheet metal screws to surface mount these.

Nathan M
April 13, 2020

As others have stated, to use the shoulder washers, one has to modify (increase) the hole size. Not a big deal, but shouldnt be required.

Jan P
March 14, 2019

Lightweight and attractive, this housing would be 5 stars if one of the holes was large enough to properly mount the mic jack without grounding it to the jack. As received, both holes are the correct size to mount a phone jack. Mounting holes have to be drilled for surface mounting.

Jim
November 10, 2017

this unit will not work in a recessed manner

Mark Z
July 27, 2015

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: On the beige model, are both sides powder coated?

Yes, both sides are powder coated.

Q: 10-01595 Does the surface with the hole cutouts sit at right angle to the flanged mounting surface, or at some other angle. Reason is I would not want jacks to angle too far away from the mounting surface, if that makes any sense ?

They are slightly less than a 90 degree angle.

View in Catalog

View Image View in Catalog