|Description||Quantity||Pot Life||Part Number||Price||Buy|
|PR2032 Resin||3/4 Gallon||-|
|PR2032 Resin||5 Gallon||-|
|PR2032/PH3660 Kit||Quart Kit||1 Hour|
|PR2032/PH3660 Kit||Gallon Kit||1 Hour|
|PR2032/PH3660 Kit||Pail Kit||1 Hour|
|PH3630 Hardener||Pint||30 Minutes|
|PH3630 Hardener||Quart||30 Minutes|
|PH3660 Hardener||Pint||1 Hour|
|PH3660 Hardener||Quart||1 Hour|
|PH3660 Hardener||2 Gallon||1 Hour|
|PH3663 Hardener||Pint||90 Minutes|
|PH3663 Hardener||Quart||90 Minutes|
|PH3663 Hardener||2 Gallon Pail||90 Minutes|
|PH3663 Hardener||30-Gallon Drum||90 Minutes|
|PH3665 Hardener||Pint||2 Hours|
|PH3665 Hardener||Quart||2 Hours|
PR2032 is a medium viscosity, unfilled, light amber laminating resin that is designed for structural production applications. Three hardeners are available for use with PR2032. PH3660, has a 1-hour pot life. When used with either of these hardeners, the system gives excellent wet-out of fiberglass, carbon and aramid fibers. Special additives have been incorporated into this system to promote chemical adhesion to fabrics made with these fibers.
The AEROPOXY systems will cure completely at room temperature, or can be given an elevated temperature cure. AEROPOXY contains no MDA (a known liver toxin and carcinogen) and meets or exceeds current OSHA requirements for safe use. It satisfies all structural, pot life and wet-out characteristics according to tests by Rutan Aircraft Factory, and RAF recommended its use for all homebuilt aircraft applications.
The best ratio on AEROPOXY is 100:27 by weight or 3 to 1 by volume. In early 1996 several improvements were made to AEROPOXY. The viscosity was lowered for easier laminating, the occasional slight surface tackiness in high humidity was eliminated, the AEROPOXY hardeners were modified to prevent any tendency to crystallize in high humidity, and the mix ratios were modified to an exact 3 to 1 by volume.
This Product should be kept fresh for the Consumer, It had settled out, and needed to be stirred
This is the greatest laminating epoxy. I use it for its high temperature capabilities.
My favorite laminating epoxy. Excellent wetout properties, great pot life and I have never had an exotherm, even with very thick layups.
Quality resin and low odor.
I use this epoxy and use a Harbor Freight scale to measure out the ratio by weight. I am not experienced at composite, and have not had any failures using this. But at 50F it takes a long time to cure....week? It did cure though!! A system that uses pumps has waste. With s small digital scale I can measure our 5 grams, or 50g. If you choose to use a pump measuring system you lack that versatility, and will increase your cost due to waste. I only gave it 4 stars because I dont have much experience with other types. I have used West System and also like it.
24hr, at room temp, is recommended. Heat can be applied to accelerate the cure time. Please see the Tech Data Sheet under the "Documents" tab for more info.
They do not come with pumps but you can use the west system pumps on the Aeropoxy kit. P/N# 01-00318.
Acetone is commonly used for cleaning un-cured epoxies. We also have Replacetone, 01-08823, which is a non-haz cleaner for un-cured epoxies.
As long as the hardeners have the same ratio they can be blended. 3630/3660/3665 are all 100:27.
Yes, this is safe to use with closed-cell polystyrene foam.