With Heat Pack option adds a shipping heat pack to keep the material from freezing while in transit. It is recommended for winter months / destinations in cold climates where the temperature may drop below freezing while in transit. If the material freezes, it is not recommended for use.
AIR QUALITY DATA
1. Application area temperature should be between 70 and 85 degrees Fahrenheit.
1. The first coat of SS Waterborne Primer/Sealer is applied as a light tack coat. Allow to dry untill tacky.
BRUSHING & ROLLING
For best results we advise spraying. But, if brushing or rolling is desired, you can achieve a nice finish with a foam brush or roller. Do not thin the primer with additional water unless it will not flow out.
Clean equipment immediately with water.
WARNING: The product may contain and/or expose you to a chemical(s) or substance(s) which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. www.P65Warnings.ca.gov
This is not a high build primer at all, even out of the can it is already too thin to spray. It needed several coats, to build up a sandable surface. I stirred up all the solids in the can. Otherwise I think it would be a good product.
STEWART SYSTEMS PRIMER SEALER WHITE QT
Great products from Stewart Systems. Goes on smooth and covers and sands well. Best of all, no smell or harmful chemicals. This is not latex. Its only transferred with water. Love it.
STEWART SYSTEMS PRIMER SEALER WHITE QT
Easy to use, didnt totally stink up the booth, covered scratches beautifully straight out of the can, and made for an excellent finished product!
This stuff cant be beat. I can prime and paint in my attached garage with no worries about fumes or harmful chemicals going into the house. The other stuff is covered wagon technology.
Needed to fill the weave in 1.3 oz fiberglass cloth that was applied over birch plywood fuselage. Two coats did the job nicely without the need of heavy “filler” primers and then mucho sanding and contouring . I lightly sanded with 220 dry before painting, but believe I could have just painted over a smooth application of this primer/sealer. JJ Sinclair
Goes on easy, sands easy........doesn’t clog sandpaper........GOOD STUFF !
I used Stewarts system before on another airplane, it is water based so not toxic and or cancer causing . It works good, easier to use and not requiring a breathing device just a mask. I have not shoot this color of paint but we shall see. Again like with the cylinders I bought a few weeks ago in 10 years I will be able to tell you how good this material is, well see how long it lasts.
I am using this on my Velocity. Its done a great job so far.
Stewart primer and paint is working out great on our AT-6 tail section,its holding its Shiny finish...we will use the Stewart process again on our Stearman..
I have used this primer for about 4 years and had good results, even when the primer was well past the claimed shelf life.
Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
Unfortunately this material is not available in an aerosol can.
You must first prep before you apply the ekoprime.
Yes, it is sandable.
That is subjective per the vendor. Typically 300-600 sq feet, but it depends on what you are painting. Maybe less if he is wanting to fill and sand, or maybe more if he is just using it to cover EkoFill for a white base coat.
Yes, it is.
Yes this primer can be applied to a painted surface that has been sanded.
No, the uses are listed as Steel, Aluminum, Fiberglass, Wood, Plastics, Concrete, PVC, Pre-Finished Siding, Steel Decks.