THE AVIATION SUPERSTORE FOR ALL YOUR AIRCRAFT & PILOT NEEDS | 877-4-SPRUCE

TCW Integrated Back Up Battery System - FAA Certified

Select Voltage
12V24V
Select Amp Hours
3 Amp Hour6 Amp Hour
Quantity
Add to Wishlist

Overview

The Integrated Battery Back-up System (IBBS) provides an engineered solution to enable an endurance bus for critical loads found in aircraft. The IBBS system provides back-up power to critical electronic loads such as EFIS, GPS, Autopilots and engine monitoring systems.

Integral to the IBBS is a lithium-iron-phosphate battery pack and a matched charging system to ensure the battery is properly charged and maintained. The system includes switching circuitry to provide a stable source of output power during both normal and emergency operations. The IBBS system also provides signals to other equipment such as EFIS systems to communicate the operating state of the back-up bus as well as the state of the battery.

The IBBS system connects to the standard aircraft power bus and provides an output to critical equipment that requires back-up power. Additionally, the IBBS system provides surge and sag protection for connected equipment, allowing operation of critical equipment during engine starting.

The IBBS system is suitable for use with equipment such as Garmin GNS and GTN series navigators, G3X series of avionics, Grand Rapids Technologies EFIS systems, Advanced Flight Systems EFIS, Dynon EFIS, and MGL EFIS, TruTrak Autopilots and EFIS, and Trio Autopilots.

IBBS products are protected by US Patent 8,189,305
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Features

  • Safe, reliable Li-Fe-PO4 chemistry
  • Fully automatic operation.
  • High performance integral charger
  • Critical backup power
  • Designed and Assembled in USA
  • FAA approved article
  • TSO-C179(a)
  • DO-311, DO-160(f)
  • US Patent 8,189,305

Specifications

IBBS-12V-3AH-CRT IBBS-12V-6AH-CRT IBBS-24V-3AH-CRT
TSO Certification: TSO-C179(b) TSO-C179(b) TSO-179(b)
Input Voltage: 13.5 – 15 volts DC for battery charging 13.5 – 15 volts DC for battery charging 26 – 32 volts DC for battery charging
Transition Voltage*: 10.5 – 11.5 volts 10.5 – 11.5 volts 21 – 23 volts
Input Current: 2.5 amps max continuous on main input for charging, 0.8 amps max for battery heater at low temps 4.0 amps continuous on main input for charging; 1.5 amps max for battery heater at low temps 3.0 amps max continuous on main input for charging
Pass-thru Current: 5 amps continuous, 10 amps peak (30 seconds) 8 amps continuous, 12 amps peak (30 seconds) 5 amps continuous, 10 amps peak (30 seconds)
Output Voltage: 10 – 14 volts DC during back-up operation 10 -14 volts DC during back-up operation 22 – 29 volts DC during back-up operation
Output Current: 5 amps continuous, 10 amps peak for radio transmissions and transient load (30 second duration max) 8 amps continuous, 12 amps peak for radio transmissions and transient load (30 second duration max) 5 amps continuous, 10 amps peak for radio transmissions and transient loads (30 second duration max)
Battery: Internal sealed Li-Fe-PO4, nominal 12.8 volts Internal sealed Li-Fe-PO4, nominal 12.8 volts Internal sealed Li-Fe-PO4, nominal 25.6 volts
Charger: Integral high-performance fast charger with cell balancing and thermal monitoring Integral high-performance fast charger with cell balancing and thermal monitoring Integral high-performance fast charger with cell balancing and thermal monitoring
Surge Protection: 34 volt active clamp, 1500w 10/1000uS waveform 34 volt active clamp, 1500w 10/1000uS waveform 51 volt active clamp, 1500 w 10/1000uS waveform
Wiring: 15 pin male D-dub on product 15 pin male D-sub on product 15 pin male D-sub on product
Enclosure: Aluminum 7.7” x 2.3” x 1.6” Aluminum 7.7” x 2.3” x 2.65” Aluminum 7.7” x 2.3” x 2.65”
Weight: 18 oz. 34 oz. 34 oz.
Temperature Range: Operating: -40° C to 60° C
Charging -40° C to 40° C
Operating: -40° C to 60° C
Charging -40° C to 40° C
Operating: -40° C to 60° C
Charging -40° C to 40° C
Connector: Standard density 15 pin D-sub, male on product Standard density 15 pin D-sub, male on product Standard density 15 pin male D-sub on product
  • Frequently Purchased With
  • Customers Also Viewed

Reviews

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

View in Catalog

View Image View in Catalog