• Wishlists
  • 877-477-7823
  • Contact Us
 
 
FREE SHIPPING ON ORDERS OVER $350 VIA UPS GROUND | 877-4-SPRUCE

EATON AEROQUIP FIRE SLEEVES

From $10.99 to $29.70
Aeroquip
P/N
I.D. Clamp
(See Accessories)
Use
With
Hose
#303
Use
With
Hose
#601
Our
P/N
Price / Ft. Buy / Ft.
AE102-8 1/2 900591B-1C -3 -4 05-01842 $10.99
Quantity
AE102-9 9/16 900591B-2C -4 -5 05-01843 $11.50
Quantity
AE102-10 5/8 900591B-2C -5 -- 05-01844 $12.50
Quantity
AE102-11 11/16 900591B-2C -- -- AE102-11 $14.50
Quantity
AE102-12 3/4 900591B-2C -6 -6 05-01839 $13.50
Quantity
AE102-13 13/16 900591B-2C -- -- AE102-13 $15.50
Quantity
AE102-14 7/8 900591B-2C -8 -8 05-04182 $16.50
Quantity
AE102-16 1 900591B-3C -10 -10 05-01841 $17.85
Quantity
AE102-18 1-1/8 900591B-3C -12 -- 05-01845 $18.85
Quantity
AE102-20 1-1/4 900591B-3C -- -12 05-01858 $22.50
Quantity
AE102-22 1-3/8 900591B-3C -16 -16 05-01859 $26.60
Quantity
AE102-24 1-1/2 900591B-3C -- -- 05-04617 $29.70
Quantity
Subtotal $0.00
Add to Wishlist

Overview

Aeroquip Firesleeve was specially developed to meet the fire resistance requirements of FAATSO - C53a OR TSO - C75. May be used for all fuel, oil, hydraulic, fire extinguisher & propeller feathering lines. "Fire-proof" hose lines as defined by FAA must withstand a direct flame for fifteen minutes under specified flow conditions without failure. Fire-resistant lines must withstand a 5-minute exposure under these conditions.

Fire-proof hose lines are obtained when the proper size Aeroquip Firesleeve is selected from the chart below and properly assembled. 900591B Clamps - used to secure firesleeve material on each end over the basic hose assembly.

See chart for correct size.

Sold by the foot.

AE102 firesleeve is used to meet the fire resistance requirements of FAA TSO-C53a and TSO-C75. This firesleeve can be identified by its orange colored outer surface. It functions effectively within a continuous operating temperature range of -65 degree to +450 degree.

  • Customers Also Viewed
  • Frequently Purchased With
  • Accessories

Reviews

High quality & finishing.

Ricardo V
April 3, 2017

This item fits and works great. The inside is soft and will flex when the hose sides into the fire sleeve. I just cut with scissors the full length of hose with fittings on and this will cover any bends of your hose. If sleeve is to long just push back and the slack will go back down the hose and still look great. One thing I found when installing the sleeve on a long hose was to use a long air blow tube from the air compressor line and insert it down the hose between the fire sleeve and the hose that the fittings are already on. I found that the blow tube should be on the end of the sleeve in the direction of travel. Blow air and just side the sleeve up the hose with now problem. I also used plugs at both ends to keep contamination out of the hose

James E
March 2, 2017

Q&A

Q: How long are each of these Aeroquip fire sleeves? I am particularly interested in the 3/4 ID.

These Aeroquip fire sleeves are priced and sold by the foot.

View in Catalog

View Image View in Catalog