|Description||Valve Stem||Part Number||Price||Buy|
|Azusa Tube # 7133 410/350 X 6||90°|
|Azusa Tube # 7130 410/350 X 4||90°|
|Azusa Tube # 7132 410/350 X 5||90°|
|Azusa Tube # 7131 340/300 X 5||90°|
|Azusa Tube # 7129 280/250 X 4||90°|
|Azusa Tube # 7141 13X6.50-6||Straight|
|Azusa Tube # 7138 800 X 6||90°|
|Azusa Tube # 7118 16-650/750 X 8||Straight|
|Azusa Tube # 7125 15-600 X 6||90°|
|Azusa Tube # 7116 11-600 X 5||90°|
|Azusa Tube # 7120 18-950 X 8||Straight|
|Azusa Tube # 7121 480/400 X 8||Straight|
|Generic Tube # TI0112 4.10 X 3.5 X 5||90°|
|Generic Tube # TI011 15-600 X 6||90°|
|Generic Tube # TI007 800 X 6||90°|
|Aero Classic Tube 400 X 6||90°|
|Azusa Tube # 7136 13-500 X 6||90°|
|Inner Tubes for most Azusa variety tires|
ULTRALIGHT & EXPERIMENTAL TUBE #7138 800 X 6
The valve stem is exactly 90°. My old one was 45°. So I could not use the new one. Now I have two tubes that I have no use for. But it’s not worth the shipping cost to send them back.
ULTRALIGHT & EXPERIMENTAL TUBE #7133 410/350X6
These are a true 90 degree valve stem with the valve stem being very near the center of the tube. These tubes work very well for the Azusa 2 piece experimental wheels. The Azusa 2 piece wheel is a split wheel with the with valve stem placement in the middle of the wheel. Meaning that each half of the wheels has a 180 degree cutout for the tube valve stem. A true 90 degree valve stem is required for this application. The rubber thickness is near heavy duty on these tubes as well. Be careful as some tubes that claim they have a 90 degree stem are actually 45 degrees and the stem is offset further tpo the side of the tube.
Tube is of good quality, good 90 degree bend but valve is not on center. I also had to modify rim to make them work.
Another reviewer said These are a true 90 degree valve stem with the valve stem being very near the center of the tube. I ordered the Azusa tube #7125, and the 90 degree valve stem was NOT even close to the center of the tube. It was about 25% of the way around the tube. I ended up modifying my wheels and moving the valve stem hole to better accommodate the offset valve stem. If I ever do end up with a proper tube, it will still fit the wheels!
Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
Yes, tube 7116 is equipped with a 90 degree bent valve stem.
06-00075 is a 90* stem. 06-01590 has a straight stem.
No, the tube 7121 has a straight valve stem.
No, this tube has a 90 degree valve stem.
From the 90 degree bend to the cap, the stem is approx 1-7/16 inches.
We have no data supporting this tubes being used for nitrogen.