works great

David G Verified Purchase

CA-7264 Quartz A/C Clock 12V

Clock looks great not sure I like the push on connector very difficult to remove when we needed to move tbe clock to another location. Thanks

James W Verified Purchase

CA-7264 Quartz A/C Clock 12V

Works as expected, installed it in my PA28-151 warrior

Timothy L Verified Purchase

CA-7264 Quartz A/C Clock 12V

Excellent clock, however I recently learned that it should be wired via the master switch unless you fly weekly, as I used to. Otherwise at 12.8 mA my Gill 24V battery (14Ah rated) will loose enough charge over 2 weeks to make starting my O235 difficult.

Great little clock - my old one went for 40 years.

Ric D Verified Purchase

CA-7264 Quartz A/C Clock 12V

Nice replacement for a wornout mechanical clock. Looks well with older style guages

Larry K Verified Purchase

CA-7264 Quartz A/C Clock 12V

Perfect replacement for my Cessna 172M. Very east to install. Fits perfect

Michael A Verified Purchase

CA-7264 Quartz A/C Clock 12V

Needs to have teflon coated wiring for airplanes.

Delivered promptly and working well.

clock is in and works fine I wonder with future up grades should I installed it.

Mine has been running since October 2017. I reset for daylight- standard time, otherwise it stays within a minute.

very happy with looks and time keeping reasonably price and well constructed

I wanted to wait a week or two to review the clock to make sure it kept working. My luck was much better that the previous reviews. Clock arrived quickly and well packaged. Change out of my old quartz clock was straight forward and replacement took about 20 minutes. So far I’m very pleased!

The second replacement clock worked! I took my old identical non-functioning clock apart to see why it would run but couldnt be adjusted to the correct time. The adjustment knob has a 1/2-ish metal gear that engages a tiny 3/16-ish plastic gear that rotates the hands when pulled backwards. The larger gear is on a shaft thats press fit into a metal plate. This pin had loosened allowing the metal gear to wobble, and the teeth on the plastic idler gear were worn off. This quartz clock is essentially a less robust copy of the original mechanical aircraft clocks with a lot of plastic part substitutions. If you are too agressive at pulling and adjusting this clock it may have a very short life, but if you are a VFR pilot that is just trying the meet the minimum FAA panel requirements list its a practical option since $160 spent every couple of years to make a quick clock swap (using an existing harness too) is likely going to be the the smallest maintenance expenditure youll suffer to keep flying. If you need a reliable clock for IFR flying this isnt what you want.

Scott P Verified Purchase

CA-7264 Quartz A/C Clock 12V

Good price, received it right on time, as usual But, you may want to examine your stock, as to the rear mounting nuts. The clock I received (albeit in great shape) has the rear mounting nuts only halfway cut through from the ferrule that runs from front to the backside of the panel. Screwdriver wont get into the cut slot enough to break the nut loose, and there doesnt appear to be any other means of freeing it. Using another two nuts will work, but the clock then has a space between it and the panel surface.

Mine quit working after six years. Now, I have to decide if I want to buy another one. If I buy a different clock, I will have to change the connector, and thats a hassle to get to at the top of the panel with hardly any room for my hand.

Good clock for the price. The rim around the edge is thick and that makes the clock face very small.

Russell R Verified Purchase

CA-7264 Quartz A/C Clock 12V

Mine worked for three years...

Only lasted 2 years and just quit working very disappointed. Im very careful to keep my cabin cover on when not flying to minimize cabin heat.

Randall H Verified Purchase

CA-7264 Quartz A/C Clock 12V

clock worked for 2 hrs then stopped then started for a day then stopped. replacement is being installed. not sure if problem only on 28v. clock says 28v.

This is a very expensive clock. We installed 2 before we got one to work and it didnt make it a year. Now we have to remove this and install something different. So Im out the price of this clock plus the new clock and the time Ive paid my A&P to install 3 clocks.

I did better than Al., my clock went for 10 minutes, thats it. Stay away from this clock.

Two out of two units defective straight out of box. They would not run! What a waste of effort, time, and money. Stay away from this clock.