|Description||ID||PN||Dash No.||Price / Ft||Length||Buy|
|Ducting Vena MTD||5/8||05-30501||-2A||$6.50|
|Ducting Vena MTD||3/4||05-30502||-3||$3.90|
|Ducting Vena MTD||7/8||05-30503||-3A||$4.35|
|Ducting Vena MTD||1||05-30504||-4||$4.35|
|Ducting Vena MTD||1-1/4||05-30505||-5||$4.45|
|Ducting Vena MTD||1-1/2||05-30506||-6||$5.35|
|Ducting Vena MTD||1-3/4||05-30507||-7||$5.95|
|Ducting Vena MTD||2||05-30508||-8||$6.55|
|Ducting Vena MTD||2-1/4||05-30509||-9||$7.50|
|Ducting Vena MTD||2-1/2||05-30510||-10||$7.50|
|Ducting Vena MTD||2-3/4||05-30511||-11||$8.50|
|Ducting Vena MTD||3||05-30512||-12||$8.75|
|Ducting Vena MTD||3-1/4||05-30513||-13||$9.65|
|Ducting Vena MTD||3-1/2||05-30514||-14||$10.50|
|Ducting Vena MTD||3-3/4||05-30515||-15||$10.50|
|Ducting Vena MTD||4||05-30516||-16||$11.50|
|Ducting Vena MTD||4-1/2||05-30518||-18||$11.50|
|Ducting Vena MTD||5||05-30520||-20||$13.50|
|Ducting Vena MTD||6||05-30524||-24||$14.50|
Sold by the foot.
Ducting used to convey air or gaseous fluids at medium temperatures and with high resistance to aging. Vena® MTD is manufactured with two fiber glass textile reinforcements and it is covered with black neoprene rubber compound and coated with non-visible steel wire. These hoses have excellent flexibility and excellent aging resistance.
These hoses are specially recommended in gas conduction at medium temperatures.
This product is manufactured with two fiber glass textile reinforcements covered with neoprene rubber compound in black and coated with non-visible steel wire.
Operational temperature range from -55ºC (-67ºF) to +125ºC (257ºF). It may reach up to 150ºC (302ºF) during short periods of time.
Stock diameter listed in ordering grid. Diameters not listed are available as a special order in full lengths only. Full factory lengths are up to 13 ft. Varies by warehouse. For lengths over 13 ft, contact sales to confirm availability.
Exactly as ordered. Item was shipped promptly. Ordered by phone - friendly phone service. Keep up the good work!
The duct material was very stiff and difficult to manipulate in tight quarters.
I used this as the air tube for my Ural motorcycle. I used the 2 pipe. Pretty easy to cut I set it perpendicular to a seam in my garage floor and used my Dremel to make a straight cut on both sides. Took about 9 for each side. It looks awesome and seals better than the original pipes
very nicely designed and manufactured product.I am going to use it for air routing on my 93 cars intake , I will tell others that are interested in it where I got it.Pilot Shop rules the day!
Nice upgrade from original CAT ducting on a PA 28-181.
That is correct. It is sold per foot, in whole units. So you need quantity 4 for 48 continuous inches, then cut off 7 inches once you get it.
CEET material is round not oval. Order using the I.D. of the unit.